Epoxy Garage Floors
Turn stained, cracked garage concrete into a clean, bright floor that sweeps out in minutes and shrugs off oil, brake fluid, and hot tires.
- 1 & 2-car garages
- Workshops
- Full flake broadcast
Garage floors, pool decks, patios, and commercial concrete — ground, repaired, and coated to stand up to Lee County humidity, salt air off the Caloosahatchee, and everyday Florida heat.
Samples shown as color guides. Call 239-910-3799 to see physical chips at your free estimate.
What we coat
Every job starts with the same prep — grinding, crack repair, and a moisture check — whether it's a two-car garage in Gateway or a warehouse floor off Colonial Blvd.
Turn stained, cracked garage concrete into a clean, bright floor that sweeps out in minutes and shrugs off oil, brake fluid, and hot tires.
Cooler, slip-resistant coatings for the spaces Fort Myers lives in year-round — built to handle pool chemicals, bare feet, and constant sun.
Outdoor living space that doesn't stain from the grill, fade in the sun, or grow slippery after a summer downpour.
Durable, easy-to-sanitize coatings for businesses that can't afford downtime — installed in sections or off-hours where needed.
Pick your look
Same prep and same topcoat on every floor — the finish is about the look and how you use the space.
Decorative vinyl flakes broadcast into the base coat to full coverage. The speckled pattern hides dirt, tire marks, and minor concrete imperfections better than any other finish, and the texture adds grip underfoot.
Best for: Garages · Pool decks
Metallic pigments are swirled through the coat as it cures, creating flowing, marble-like movement. No two metallic floors ever look the same — each one is mixed and laid by hand on your slab.
Best for: Show garages · Showrooms · Lanais
A single, uniform color with a clean industrial look. Easy to sweep, easy to spot a dropped bolt or a spill, and the most straightforward finish to touch up years down the road.
Best for: Commercial · Workshops · Warehouses
How it gets done
An epoxy floor is only as good as what's underneath it. This is the process on every job — no steps skipped, because skipped prep is why coatings peel.
The concrete is diamond-ground to open the pores and remove old paint, sealers, and surface grime, so the coating bonds mechanically to the slab.
Cracks, spalls, and control-joint damage are filled and ground flush, so repairs don't telegraph through the finished floor.
The slab is tested for moisture vapor. In Fort Myers' high water table, coating over a wet slab is the #1 cause of failure — if it's wet, we address it first.
The base coat goes down and, on flake floors, decorative flake is broadcast to full coverage while the coat is wet. Metallic and solid finishes are laid in this step too.
A clear, UV-stable protective topcoat seals everything in — the layer that resists hot tires, chemicals, sun fade, and salt air.
Local, on purpose
Fort Myers concrete lives a hard life. Summer humidity pushes moisture up through slabs, afternoon storms soak pool decks daily, and salt air drifting in off the Caloosahatchee River works on every exposed surface. A coating system that works in a dry climate can blister and peel here in a single rainy season.
That's why every floor we install starts with a moisture check and ends with a UV-stable topcoat, and why our installs follow Lee County hurricane code requirements for the work we do. The goal is a floor that still looks right after hurricane season, not just after install day.
Questions about whether your slab is a good candidate? Call 239-910-3799 and ask — a free estimate includes the moisture check.
Straight answers
A properly prepped epoxy floor is one of the toughest surfaces you can put on concrete. It resists oil, gasoline, brake fluid, and most household chemicals, and it won't stain or dust the way bare concrete does. The durability comes from the prep: diamond grinding gives the coating a mechanical bond to the slab, and the clear topcoat takes the daily wear so the color coat underneath doesn't have to.
What shortens a floor's life isn't use — it's moisture trapped under the coating and skipped prep. That's why both are built into every job we do.
Hot-tire pickup happens when a hot tire sits on a coating that hasn't fully bonded or isn't rated for the heat — the tire cools, contracts, and pulls the coating off the concrete. It's the most common failure of thin, big-box-store epoxy kits.
A professionally ground slab, a full base coat, and a proper protective topcoat are what prevent it. When the bond to the concrete is stronger than the pull of the tire, the floor stays down. Parking on it daily in Florida summer heat is exactly what this system is installed for.
Two ways. First, humidity: Fort Myers slabs pull moisture from the ground, and if a coating goes down over a damp slab, that vapor pressure can blister and delaminate it. We test moisture before coating and address it if the slab reads wet.
Second, salt air: homes near the Caloosahatchee and the Gulf get a constant salt film on outdoor concrete. Salt is hard on bare concrete and on metal, but a sealed epoxy surface doesn't absorb it — it rinses off. For pool decks, patios, and lanais, that sealed surface is a big part of the point.
Most residential floors — garages, lanais, patios — take about two days of work: day one is grinding, crack repair, the moisture check, and the base coat with flake; day two is the topcoat once the base has cured.
After the topcoat, the floor needs cure time before it goes back into service: light foot traffic comes first, and vehicles come last — we'll give you the exact walk-on and drive-on times for your floor when we finish, since they depend on the finish and the weather. Commercial floors are scheduled around your business, in sections or off-hours where needed.
It depends on the size of the slab, its condition, and the finish you choose — a cracked, previously painted garage costs more to prep than clean bare concrete. Rather than quote a number that turns out wrong, we measure and inspect in person: call 239-910-3799 for a free estimate and you'll get a real price for your actual floor.
Free estimate
The fastest way to a real price is a quick call — we measure, check the slab's moisture, and price your actual floor.
Tell us what surface you're coating and roughly how big it is, and we'll take it from there.
Tap to call239-910-3799Prefer to write it out? Use the quote form — it opens your email app with your details ready to send.